Free Cisco 300-410 Exam Dumps and 300-410 Exam Questions

Question No: 11

MultipleChoice

Exhibit:

An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP peers. Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?

Options

AR1 and R4

BR1 and R5

CR4 and R5

DR2 and R5

Question No: 12

MultipleChoice

Clients on ALS2 receive IPv4 and IPv6 addresses but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses. Which action on DSW1 allows clients on ALS1 to receive IPv6 addresses?

Options

AConfigure DSW1(config-if)#ipv6 helper address 2002:404:404::404:404

BConfigure DSW1(dhcp-config)#default-router 2002:A04:A01::A04:A01

CConfigure DSW1(config)#ipv6 route 2002:404:404:404:404/128 FastEthernet1/0

DConfigure DSW1(config-if)#ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2

Question No: 13

MultipleChoice

Exhibit:

BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?

(Choose two)

Options

AConfigure BGP in the COPP-CRITICAL-7600 ACL

BConfigure a higher value for CIR under the default class to allow more packets during peak traffic

CConfigure a higher value for CIR under the class COPP-CRITICAL-7600

DConfigure a three-color policer instead of two-color policer under class COPP-CRITICAL-
7600

EConfigure IP CEF to CoPP policy and BGP to work

Question No: 14

MultipleChoice

Refer to the exhibit.

an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

Options

AConfigure EIGRP to receive 192.168.32.0 route with lower admin distance.

BA. Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

CA. Configure EIGRP to receive 192.168.32.0 route with lower metric.

DA. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Question No: 15

MultipleChoice

Refer to the exhibit.

An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?

Options

AHQ_R3(config)# ip sla responder
HQ_R3(config)# ip sla responder icmp-echo 172.16.35.1

BBRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 192.168.100.2

CHQ R3(config)# Ip sla responder
HQ R3(config)# Ip sla responder Icmp-echo 172.16.35.5

DBRANCH(config)# Ip sla 1
BRANCH(config-ip-sta)# Icmp-echo 192.168.100.1

Question No: 16

MultipleChoice

Refer to the exhibit.

The Los Angeles and New York routers are receiving routes from Chicago but not from each other Which configuration fixes the issue?

Options

AInterface Tunnel1
no ip split-horizon eigrp 111

BInterface Tunnel1
Ip next-hop-self elgrp 111

CInterface Tunnel1
tunnel mode Ipsec Ipv4

DInterface Tunnel1
tunnel protection ipsec profile IPSec-PROFILE

Question No: 17

MultipleChoice

Refer to the exhibit.

The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?

Options

AEnable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command

BDisable IPv6 on the E 0/0 interface using the no ipv6 enable command

CEnable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command

DDisable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.

Question No: 18

MultipleChoice

Refer to the exhibit.

An engineer receives this error message when trying to access another router m-band from the serial interface connected to the console of R1. Which configuration is needed on R1 to resolve this issue?

Options

AOption A

BOption B

COption C

DOption D

Question No: 19

MultipleChoice

Refer to the exhibit.

Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

Options

AConfigure EIGRP to receive 192.168.32.0 route with lower admin distance.

BA. Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

CA. Configure EIGRP to receive 192.168.32.0 route with lower metric.

DA. Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Question No: 20

MultipleChoice

A network engineer must configure a DMVPN network so that a spoke establishes a direct path to another spoke if the two must send traffic to each other. A spoke must send traffic directly to the hub if required. Which configuration meets this requirement?

A)

B)

C)

D)

Options

AOption

BOption

COption

DOption