Cisco Exam 200-301 Topic 1 Question 90 Discussion

Actual exam question for Cisco's 200-301 exam

Question #: 90
Topic #: 1

Refer to the exhibit.

Connectivity between three routers has been established, and IP services must be configured jn the order presented to complete the implementation Tasks assigned include configuration of NAT, NTP, DHCP, and SSH services.

1. All traffic sent from R3 to the R1 Loopback address must be configured for NAT on R2. All source addresses must be translated from R3 to the IP address of Ethernet0/0 on R2, while using only a standard access list named NAT To verify, a ping must be successful to the R1 Loopback address sourced from R3. Do not use NVI NAT configuration.

2. Configure R1 as an NTP server and R2 as a client, not as a peer, using the IP address of the R1 Ethernet0/2 interface. Set the clock on the NTP server for midnight on January 1, 2019.

3. Configure R1 as a DHCP server for the network 10.1.3.0/24 in a pool named TEST. Using a single command, exclude addresses 1-10 from the range. Interface Ethernet0/2 on R3 must be issued the IP address of 10.1.3.11 via DHCP.

4. Configure SSH connectivity from R1 to R3, while excluding access via other remote connection protocols. Access for user root and password Cisco must be set on router R3 using RSA and 1024 bits. Verify connectivity using an SSH session from router R1 using a destination address of 10.1.3.11. Do NOT modify console access or line numbers to accomplish this task.

ASee the Explanation below

Show Suggested Answer

Suggested Answer: A

Answer as below configuration:

conf t

R1(config)#ntp master 1

R2(config)#ntp server 10.1.2.1

Exit

Router#clock set 00:00:00 jan 1 2019

ip dhcp pool TEST

network 10.1.3.0 255.255.255.0

ip dhcp exluded-address 10.1.3.1 10.1.3.10

R3(config)#int e0/3

R3(config)#int e0/2

ip address dhcp

no shut

crypto key generate RSA

1024

Copy run start

by Devon at Jul 05, 2024, 04:53 PM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Dean

4 months ago

Haha, I bet the exam writers love to throw in those little 'gotchas' like the clock settings on the NTP server. Gotta stay on your toes for sure!

upvoted 0 times

Rima

3 months ago

Definitely, you have to pay attention to every instruction.

upvoted 0 times

...

Quentin

4 months ago

Yeah, those little details can really trip you up.

upvoted 0 times

...

Eve

4 months ago

SSH connectivity is usually not too difficult, but the requirement to use RSA and a specific bit size could be tricky. I better double-check my syntax.

upvoted 0 times

Laurel

4 months ago

It's always good to verify your configuration before testing SSH connectivity.

upvoted 0 times

...

Kati

4 months ago

I agree, the RSA and specific bit size requirement can be tricky.

upvoted 0 times

...

Tyisha

4 months ago

Make sure you double-check your syntax for the SSH configuration.

upvoted 0 times

...

Alex

4 months ago

Yes, and setting up NTP server on R1 and DHCP server on R1 for network 10.1.3.0/24 are the next tasks.

upvoted 0 times

...

Antonio

4 months ago

I think configuring NAT on R2 for traffic from R3 to R1 Loopback address is the first step.

upvoted 0 times

...

Tomas

4 months ago

DHCP configuration is always a pain, especially when you have to exclude a specific range of addresses. I hope I don't mess that up.

upvoted 0 times

...

Izetta

5 months ago

Configuring the NTP server and client should be easy, but setting the clock on the server to a specific date might be a trick question.

upvoted 0 times

Ashton

4 months ago

As long as we follow the instructions carefully, we should be able to configure the NTP services correctly.

upvoted 0 times

...

Elly

4 months ago

I agree, setting the clock on the server for a specific date might require some extra steps.

upvoted 0 times

...

Brett

4 months ago

Yeah, configuring the NTP server and client is straightforward, just need to pay attention to the details.

upvoted 0 times

...

Beata

4 months ago

Setting the clock on the NTP server is a bit tricky, but it can be done easily.

upvoted 0 times

...

Alex

5 months ago

I agree, we need to carefully follow the instructions.

upvoted 0 times

...

Tijuana

5 months ago

This question looks pretty straightforward, but I wonder if the NAT configuration will trip me up. Should I use the standard access list or try something else?

upvoted 0 times

Man

4 months ago

Don't worry, just follow the instructions and use the standard access list named NAT for the NAT configuration on R2.

upvoted 0 times

...

Blair

4 months ago

I agree, using the standard access list named NAT is the correct approach for the NAT configuration.

upvoted 0 times

...

Nada

4 months ago

You should definitely use the standard access list named NAT for the NAT configuration on R2.

upvoted 0 times

...

Glory

4 months ago

Don't overthink it, just follow the steps provided and you should be fine with the NAT configuration.

upvoted 0 times

...

Isidra

4 months ago

I agree, sticking to the instructions will ensure you complete the task correctly.

upvoted 0 times

...

Gerald

4 months ago

You should follow the instructions and use the standard access list named NAT for the NAT configuration.

upvoted 0 times

...

Antonio

5 months ago

This question seems challenging.

upvoted 0 times

...