Cisco Exam 300-435 Topic 4 Question 69 Discussion

Actual exam question for Cisco's 300-435 exam

Question #: 69
Topic #: 4

[All 300-435 Questions]

Refer to the exhibit.

The configuration commands are entered in CLI config mode to configure a static telemetry

subscription on a Cisco IOS XE device. The commands are accepted by the device, but the consumer receives

no telemetry dat

a. Which change must be made to ensure that the consumer receives the telemetry data?

AThe IP address of the receiver must be set.

BThe stream type must be set to YANG.

CThe update policy period must be shortened.

DThe sender IP address must be set.

Show Suggested Answer

Suggested Answer: A

b_1610_programmability_cg/model_driven_telemetry.html

by Shanice at Jul 11, 2024, 09:57 PM

Limited Time Offer

25%

Off

Get Premium 300-435 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Melvin

4 months ago

I'm stumped. Is the correct answer none of the above? Maybe the telemetry subscription is configured correctly, and the issue is with the consumer's setup. Who knows?

upvoted 0 times

Benton

4 months ago

C) The update policy period must be shortened.

upvoted 0 times

...

Hillary

4 months ago

B) The stream type must be set to YANG.

upvoted 0 times

...

Melinda

4 months ago

A) The IP address of the receiver must be set.

upvoted 0 times

...

Beckie

5 months ago

I think shortening the update policy period could also be a solution to ensure data is received.

upvoted 0 times

...

Louisa

5 months ago

Haha, D for sure! The sender IP address must be set. How else will the consumer know where the data is coming from? This question is a joke.

upvoted 0 times

Florinda

3 months ago

Definitely D. It's a basic requirement for the consumer to receive the telemetry data.

upvoted 0 times

...

Nicolette

3 months ago

Yeah, without the sender IP address, how will the consumer know where the data is coming from?

upvoted 0 times

...

Shawna

3 months ago

I think D is the correct answer too. The sender IP address must be set.

upvoted 0 times

...

Curtis

4 months ago

I agree with you, D is the right answer. The sender IP address must be set.

upvoted 0 times

...

Janae

4 months ago

No way, it's definitely B. The stream type must be set to YANG.

upvoted 0 times

...

Dorothy

4 months ago

I think A is the correct answer. The IP address of the receiver must be set.

upvoted 0 times

...

Noelia

5 months ago

I believe changing the stream type to YANG might also help in receiving the telemetry data.

upvoted 0 times

...

Evan

5 months ago

I'm going with B. The stream type must be set to YANG. That's the whole point of this telemetry thing, isn't it?

upvoted 0 times

Jose

4 months ago

Yeah, that sounds like the right move to make. YANG is essential for telemetry data.

upvoted 0 times

...

Edda

5 months ago

I agree, setting the stream type to YANG should definitely help.

upvoted 0 times

...

Evette

5 months ago

I agree with Lonny, setting the IP address of the receiver should fix the issue.

upvoted 0 times

...

Lonny

5 months ago

I think the IP address of the receiver must be set.

upvoted 0 times

...

Lilli

5 months ago

The answer is obviously A. The IP address of the receiver must be set for the consumer to receive the telemetry data. How else would the data get there?

upvoted 0 times