Free Preparation Discussions
MENU
Cisco 200-301 Exam Questions
- Topic 1: Network Fundamentals: The topic explains the role and function of network components. It also discusses the specifications of network topology architectures. Moreover, it Configure and verify IPv4 addressing and subnetting and IPv6 addressing and prefixes. You also encounter questions about explaining virtualization fundamentals and describing switching concepts. Lastly, it compares physical interface and cabling types and TCP to UDP.
- Topic 2: Network Access: In this topic questions about configuring and verifying VLANs, inter-switch connectivity, Layer 2 discovery protocols, and Layer 2/Layer 3. It also describes Cisco Wireless Architectures and AP modes, physical infrastructure connections of WLAN components, and AP and WLC management access connections.
- Topic 3: Connectivity: The topic connectivity discusses configuring and verifying IPv4 and IPv6 static routing, and single area OSPFv2. It also determines how a router makes a forwarding decision by default and describes the purpose, functions, and concepts of first-hop redundancy protocols.
- Topic 4: IP Services: It explains the forwarding per-hop behavior (PHB) for QoS, the role of DHCP and DNS within the network, and the function of SNMP in network operations. Moreover, it discusses configuring and verifying NTP operating in a client and server mode, inside source NAT using static and pools, DHCP client, and relay. Lastly, the topic focuses on the capabilities and functions of TFTP/FTP in the network and the use of syslog features.
- Topic 5: Security Fundamentals: The topic defines key security concepts, security program elements, and wireless security protocols. Moreover, it focuses on configuring and verifying device access control, Layer 2 security features, and WLAN within the GUI.
- Topic 6: Automation and Programmability: In this topic questions about explaining how automation impacts network management, comparing traditional networks with controller-based networking, and describing characteristics of REST-based APIs. It also delves into components of JSON-encoded data, capabilities of configuration management mechanisms Puppet, traditional campus device management with Cisco DNA Center-enabled device management, and controller-based, software-defined architecture.
Free Cisco 200-301 Exam Actual Questions
Note: Premium Questions for 200-301 were last updated On Apr. 01, 2025 (see below)
Refer to the exhibit.
An engineer configures interface fa0/1 on SW1 and SW2 to pass traffic from two different VLANs. For security reasons, company policy requires the native VLAN to be set to a nondefault value. Which configuration meets this requirement?
A)
B)
C)
D)
Topic 5, Simulations / Lab
Refer to the exhibit. The user has connectivity to devices on network 192.168.3 0/24 but cannot reach users on the network 10.10.1.0724.
What is the first step to verify connectivity?
Refer to the exhibit.
Refer to the exhibit. A network administrator is configuring a router for user access via SSH. The service-password encryption command has been issued. The configuration must meet these requirements:
* Create the username as CCUser.
* Create the password as NA!2Scc.
* Encrypt the user password.
What must be configured to meet the requirements?
A HCP pool has been created with the name CONTROL. The pool uses the next to last usable IP address as the default gateway for the DHCP clients. The server is located at 172.16 32.15. What is the step in the process for clients on the 192.168.52.0/24 subnet to reach the DHCP server?
DHCP and broadcasts: DHCP clients use broadcasts to find a DHCP server, but broadcasts are typically limited to the local subnet. Since the DHCP server (172.16.32.15) is on a different subnet than the clients (192.168.52.0/24), the clients' broadcast requests won't reach it.
ip helper-address: This command is used on a router (or layer 3 switch) to forward DHCP broadcasts to a specific IP address (the DHCP server) on a different subnet. This allows clients to discover and obtain IP address information from a DHCP server that is not on their local network.
Refer to the exhibit. The user has connectivity to devices on network 192.168.3 0/24 but cannot reach users on the network 10.10.1.0724.
What is the first step to verify connectivity?
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Malcom
Bettina
6 days agoAbraham
20 days agoKeith
29 days agoAlexis
1 months agoMammie
2 months agoLaurel
2 months agoLaurel
2 months agoMarva
2 months agoMeaghan
3 months agoKristal
3 months agoPaola
3 months agoHoa
3 months agoMignon
4 months agoBoris
4 months agoArmando
4 months agoLing
4 months agoJenelle
4 months agoMadonna
5 months agoJustine
5 months agoGeraldine
5 months agoGeorgiana
5 months agoLong
5 months agoMalika
6 months agoGlenn
6 months agoInocencia
6 months agoCiara
6 months agoLacresha
6 months agoEmile
7 months agoJettie
7 months agoAnnelle
8 months agoCarman
9 months agoXenia
9 months agoAimee
9 months agoRicarda
9 months agoEleanor
10 months agoHenry
10 months agoNoah
10 months agoIsabella
10 months agoAdam
10 months agoJames Amiri
12 months ago