CompTIA Exam CV0-004 Topic 5 Question 12 Discussion

Actual exam question for CompTIA's CV0-004 exam

Question #: 12
Topic #: 5

[All CV0-004 Questions]

You are a cloud engineer working for a cloud service provider that is responsible for an

IaaS offering.

Your customer, who creates VMs and manages virtual storage, has noticed I/O bandwidth issues and low IOPS (under 9000).

Your manager wants you to verify the proper storage configuration as dictated by your service level agreement (SLA).

The SLA specifies:

. Each SFP on the hypervisor host must be set to the maximum link speed

allowed by the SAN array. . All SAN array disk groups must be configured in a RAID 5.

. The SAN array must be fully configured for redundant fabric paths. . IOPS should not fall below 14000

INSTRUCTIONS

Click on each service processor to review the displayed information. Then click on the drop-down menus to change the settings of each device as necessary to conform to the SLA requirements.

ASee the explanation for complete solution

Show Suggested Answer

Suggested Answer: A

Based on the SLA requirements and the information provided in the diagram:

For the Hypervisor:

Slot A fiber channel card:

Port 1 link speed should be set to 16 Gbps since it's connected to Fabric switch A which supports 16 Gbps.

Port 2 link speed should be set to 8 Gbps because it's connected to Fabric switch B which supports up to 8 Gbps.

Slot B fiber channel card:

Port 1 link speed should be set to 16 Gbps since it's connected to Fabric switch A which supports 16 Gbps.

Port 2 link speed should be set to 8 Gbps because it's connected to Fabric switch B which supports up to 8 Gbps.

by Edda at Jun 22, 2024, 01:14 PM

Limited Time Offer

25%

Off

Get Premium CV0-004 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Angella

5 months ago

Looks like we need to crank up the SAN array to 11 to make sure it hits those IOPS targets. Maybe we can overclock the hypervisor while we're at it!

upvoted 0 times

Ty

4 months ago

Don't forget to ensure the SAN array has redundant fabric paths for full configuration.

upvoted 0 times

...

Shawna

4 months ago

We should also configure all SAN array disk groups in RAID 5 for redundancy.

upvoted 0 times

...

Jacinta

4 months ago

I agree, we need to make sure each SFP is set to the maximum link speed.

upvoted 0 times

...

Page

4 months ago

Let's check the settings on the service processors to meet the SLA requirements.

upvoted 0 times

...

Cory

5 months ago

What is this, a storage configuration quiz? I could do this in my sleep. Let's get it done and move on to the next challenge!

upvoted 0 times

Tammara

4 months ago

I agree, let's make sure the IOPS are above 14000 and the fabric paths are redundant. We got this!

upvoted 0 times

...

Jerilyn

4 months ago

I think we need to adjust the settings on the SAN array disk groups to RAID 5 for redundancy.

upvoted 0 times

...

Vilma

4 months ago

Let's review the information on the service processors and make sure everything is set to conform to the SLA requirements.

upvoted 0 times

...

Rosann

4 months ago

I agree, let's make the necessary changes and get this storage configuration sorted out.

upvoted 0 times

...

Dahlia

4 months ago

I think we need to adjust the settings to ensure the IOPS are above 14000 as per the SLA.

upvoted 0 times

...

Carmela

4 months ago

Let's review the settings on each service processor and make sure they conform to the SLA requirements.

upvoted 0 times

...

Lindsey

5 months ago

I bet the customer is sweating bullets over those IOPS numbers. Gotta get that up to 14000 or they're going to be furious.

upvoted 0 times

Maira

4 months ago

User 2

upvoted 0 times

...

Alaine

5 months ago

User 1

upvoted 0 times

...

Lang

5 months ago

That's right. We also need to ensure the SAN array is fully configured for redundant fabric paths.

upvoted 0 times

...

Julene

5 months ago

According to the SLA, all SAN array disk groups must be configured in RAID 5.

upvoted 0 times

...

Lang

5 months ago

I agree, the I/O bandwidth issues and low IOPS are concerning.

upvoted 0 times

...

Stanton

5 months ago

Redundant fabric paths, huh? Better not let the SAN array go down or it's going to be a real nightmare.

upvoted 0 times

Osvaldo

5 months ago

User 2

upvoted 0 times

...

Freeman

5 months ago

User 1

upvoted 0 times

...

Mertie

6 months ago

Hmm, looks like we need to configure the SAN array to RAID 5 to meet the SLA. Hope the IOPS don't drop too low.

upvoted 0 times

Brittani

5 months ago

User 2

upvoted 0 times

...

Tabetha

5 months ago

User 1

upvoted 0 times

...

Julene

6 months ago

I think we need to check the storage configuration for the VMs.

upvoted 0 times

...