CWNP CWAP-404 Exam Questions

The Group Key Handshake consists of two frames excluding any Ack frames that may be required. The Group Key Handshake is used to distribute and update the Group Temporal Key (GTK) for encrypting broadcast and multicast traffic. The AP initiates the Group Key Handshake by sending a Group Key Message 1 frame to a STA, which contains the new GTK and other information. The STA responds with a Group Key Message 2 frame to the AP, which confirms the receipt of the GTK and other information. After this, both the AP and the STA can use the new GTK for encryption and decryption of broadcast and multicast traffic . Reference: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 246; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 247.

The most likely issue that can be identified from the spectrum analysis is a power mismatch between the APs and the clients. A power mismatch occurs when the APs transmit at a higher power level than the clients, or vice versa. This can cause asymmetric communication, where one side can hear the other, but not vice versa. This can result in poor performance, disconnections, or packet loss. A spectrum analysis can reveal a power mismatch by showing different signal amplitudes or RSSI values for the APs and the clients on the same channel or frequency. The other options are not correct, as they cannot be identified from the spectrum analysis alone. The tablets' SSID, power save mode, and noise floor can be determined by using other tools or methods, such as protocol analysis, site survey, or device configuration.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 79-80

802.11k Neighbor Requests and Neighbor Reports are sent in Action frames. An Action frame is a Management frame that is used to perform various operations or functions related to the operation or maintenance of a wireless network. An Action frame consists of a Category field that indicates the type of action being performed, and a variable-length Action Details field that contains specific information related to the action. For example, an Action frame with a Category field value of 5 indicates a Radio Measurement action, and the Action Details field may contain a Neighbor Request or a Neighbor Report subelement . Reference: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 207; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 208; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434.

The function of 802.11 management frames is to manage the BSS. A BSS (Basic Service Set) is a group of STAs (stations) that share a common SSID (Service Set Identifier) and communicate with each other through an AP (access point) or directly in an ad hoc mode. Management frames are one of the three types of 802.11 frames, along with control and data frames. Management frames are used to establish, maintain, and terminate associations between STAs and APs, as well as to advertise and discover BSSs, exchange security information, report errors, and perform other management functions. The other options are not correct, as they are not functions of 802.11 management frames. Prioritizing network administration traffic, communicating configuration changes between WLAN controller and APs, and managing the flow of data are functions of other types of frames or protocols.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 120-121

The interframe space that would be expected between a CTS (Clear to Send) and a Data frame is SIFS (Short Interframe Space). A SIFS is the shortest interframe space that is used for high-priority transmissions, such as ACKs (Acknowledgements), CTSs, or data frames that are part of a fragmentation or aggregation process. A SIFS is a fixed value that depends on the PHY type and channel width. A CTS and a Data frame are part of a virtual carrier sense mechanism called RTS/CTS (Request to Send/Clear to Send), which is used to avoid collisions and hidden node problems in wireless transmissions. When a STA (station) wants to send a data frame, it first sends an RTS frame to the intended receiver, indicating the duration of the transmission. The receiver then responds with a CTS frame, also indicating the duration of the transmission. The other STAs in the vicinity hear either the RTS or the CTS frame and update their NAV (Network Allocation Vector) timers accordingly, deferring their access to the medium until the transmission is over. The sender then sends the data frame after waiting for a SIFS, followed by an ACK frame from the receiver after another SIFS. The other options are not correct, as they are not used between a CTS and a Data frame. A PIFS (PCF Interframe Space) is used for medium access by the PCF (Point Coordination Function), which is an optional and rarely implemented polling-based mechanism that provides contention-free service for time-sensitive traffic. An AIFS (Arbitration Interframe Space) is used for medium access by different ACs (Access Categories), which are logical queues that correspond to different QoS (Quality of Service) levels for different types of traffic. An AIFS is a variable interframe space that depends on the AIFSN (Arbitration Interframe Space Number) value of each AC. A DIFS (Distributed Interframe Space) is used for medium access by the DCF (Distributed Coordination Function), which is the default and mandatory contention-based mechanism that provides best-effort service for normal traffic.Reference:[Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 166-167; Chapter 7: QoS Analysis, page 194-195