Free Preparation Discussions
MENU
Fortinet FCP_FGT_AD-7.4 Exam Questions
- Fortinet Certified Professional Certifications
- Fortinet FCP Fortinet Certified Professional Security Operations Certifications
- Topic 1: Deployment and System Configuration: This section covers how to set up initial configurations, implement Fortinet Security Fabric, and configure an FGCP HA cluster; diagnose resources and connectivity.
- Topic 2: Firewall Policies and Authentication: This topic covers how to set firewall policies, configure SNAT/DNAT, implement authentication methods, and deploy FSSO.
- Topic 3: Content Inspection: This section covers how to inspect encrypted traffic, configure inspection modes, apply web filtering, manage applications, set antivirus modes, and implement IPS for security.
- Topic 4: Routing: This section covers how to set up packet routing with static routes and configure SD-WAN for efficient traffic load balancing.
- Topic 5: VPN: In this section, the focus is on how to configure SSL VPNs for secure network access and implement meshed or redundant IPsec VPNs.
Free Fortinet FCP_FGT_AD-7.4 Exam Actual Questions
Note: Premium Questions for FCP_FGT_AD-7.4 were last updated On Apr. 15, 2025 (see below)
Refer to the exhibit.
Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?
For traffic that does not match any of the defined SD-WAN rules, the default implicit SD-WAN rule is applied. By default, the FortiGate uses a 'source-destination IP-based' algorithm, which means all traffic from a specific source IP to a specific destination IP is sent through the same interface. This ensures that a consistent path is used for traffic between the same source and destination IP addresses. Options B, C, and D do not apply because the default algorithm does not prioritize by latency, session count, or source IP alone.
FortiOS 7.4.1 Administration Guide: SD-WAN Load Balancing Algorithms
Which statement about the deployment of the Security Fabric in a multi-VDOM environment is true?
'When you configure FortiGate devices in multi-vdom mode and add them to the Security Fabric, each VDOM with its assigned ports is displayed when one or more devices are detected. Only the ports with discovered and connected devices appear in the Security Fabric view and, because of this, you must enable Device Detection on ports you want to have displayed in the Security Fabric. VDOMs without ports with connected devices are not displayed. All VDOMs configured must be part of a single Security Fabric.'
FortiGate is operating in NAT mode and has two physical interfaces connected to the LAN and DMZ networks respectively.
Which two statements are true about the requirements of connected physical interfaces on FortiGate? (Choose two.)
Both interfaces must have directly connected routes on the routing table
In NAT mode, each interface must have a corresponding entry in the routing table, typically as a directly connected route, to route traffic between them effectively.
Both interfaces must have IP addresses assigned
In NAT mode, each interface must have an IP address to participate in routing and NAT operations. The IP addresses allow the FortiGate to forward traffic between different network segments.
Refer to the exhibit.
A network administrator is troubleshooting an IPsec tunnel between two FortiGate devices. The administrator has determined that phase 1 status is up, but phase 2 fails to come up.
Based on the phase 2 configuration shown in the exhibit, which two configuration changes will bring phase 2 up? (Choose two.)
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, VIP configuration, firewall policy. and the sniffer CLI output on the FortiGate device.
The WAN (port1) interface has the IP address 10.200.1.1 /24.
The LAN (port3) interface has the IP address 10.0.1.254/24.
The webserver host (10. 0.1. 10) must use its VIP external IP address as the source NAT (SNAT) when It pings remote server (10.200.3.1).
Which two statements are valid to achieve this goal? (Choose two.)
Enable NAT on the Allow_access firewall policy (A):
The Allow_access firewall policy must have NAT enabled to allow the webserver to use its VIP external IP address (10.200.1.10) as the source NAT when initiating traffic, such as pings, to the remote server.
Disable port forwarding on the VIP object (D):
Port forwarding is designed for specific port mapping, typically for services like HTTP or HTTPS. To use the VIP external IP as a source NAT, port forwarding should be disabled. Disabling port forwarding ensures that the full VIP IP address is used without being tied to specific ports.
Why other options are not correct:
B . Create a new firewall policy before Internet_Access for the webserver and apply the IP pool:
This is unnecessary as the VIP object itself is used for SNAT in this case, and an additional firewall policy is not required.
C . Disable NAT on the Internet_Access firewall policy:
Disabling NAT on this policy would prevent the NAT functionality needed for the webserver to use the VIP external IP address as the source IP.
Thus, enabling NAT on the Allow_access policy and disabling port forwarding on the VIP configuration are the valid steps to achieve the goal.
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Weldon
2 days agoJerlene
5 days agoChu
22 days agoColton
1 months agoMaryann
1 months agoDenae
2 months agoJennie
2 months agoJacquline
2 months agoNakisha
3 months agoAdell
3 months agoStefanie
3 months agoEmmett
3 months agoJerrod
4 months agoVincenza
4 months agoDong
4 months agoLaurel
4 months agoMarget
4 months agoRanee
5 months agoShaniqua
5 months agoYolande
5 months agoChantell
5 months agoPilar
5 months agoIlona
5 months agoRebbecca
6 months agoRaina
6 months agoLisha
6 months agoIra
6 months agoMose
6 months agoTracey
7 months agoKati
7 months agoMerlyn
7 months agoCornell
7 months agoMaybelle
7 months agoRene
8 months ago