Cyber Monday 2024! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

HP Exam HPE2-W09 Topic 1 Question 56 Discussion

Actual exam question for HP's HPE2-W09 exam
Question #: 56
Topic #: 1
[All HPE2-W09 Questions]

Two ArubaOS-CX switches ate part of a Virtual Switching Extension (V5X) fabric. Is this a guideline for configuring the switches' link-up delay settings?

Solution: The link-up delay timer is only required when split-recovery is disabled.

Show Suggested Answer Hide Answer
Suggested Answer: B

Virtual Switching Extension (VSX) is a high-availability technology that allows two ArubaOS-CX switches to operate as a single logical device. VSX link-up delay is a feature that delays bringing downstream VSX links up, following a VSX device reboot or an ISL flap. This prevents traffic blackholing or loops due to transient conditions. The link-up delay timer is not only required when split-recovery is disabled. Split-recovery is another feature that prevents traffic blackholing or loops when the ISL link fails and then recovers. Split-recovery works by disabling the secondary VSX member's downstream links until it synchronizes with the primary member. However, split-recovery does not cover all scenarios where traffic blackholing or loops can occur, such as when both VSX members reboot simultaneously or when the ISL flaps rapidly.Therefore, it is recommended to configure the link-up delay timer even when split-recovery is enabled1. Therefore, this is not a valid guideline for configuring the switches' link-up delay settings.


by Sheron at Apr 14, 2024, 04:54 PM

Limited Time Offer

25%

Off

Get Premium HPE2-W09 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Gene
6 months ago
I think if split-recovery is enabled, the switches would be able to recover from failures quickly without needing the delay timer.
upvoted 0 times
...
Dana
6 months ago
But what if split-recovery is enabled? Would the link-up delay timer be required then?
upvoted 0 times
...
Grover
6 months ago
I agree, if split-recovery is disabled, then the link-up delay timer is not needed.
upvoted 0 times
...
Bev
7 months ago
No, I don't think it's necessary.
upvoted 0 times
...
Elly
7 months ago
No, I think the link-up delay should be configured regardless of split-recovery status.
upvoted 0 times
...
Nieves
7 months ago
I agree, it makes sense to configure the link-up delay settings based on split-recovery.
upvoted 0 times
...
Nenita
7 months ago
Yes, the link-up delay timer is only needed when split-recovery is disabled.
upvoted 0 times
...
Kindra
8 months ago
Haha, yeah, it's like they're daring us to admit we don't know everything about every Aruba networking feature. I'm just going to do my best and hope for the best!
upvoted 0 times
...
Rusty
8 months ago
You know, I bet the exam writers are just trying to trip us up with these super specific questions. They probably want to see how well we can apply our networking knowledge to these edge cases.
upvoted 0 times
...
William
8 months ago
Hmm, I'm not too familiar with Virtual Switching Extension (V5X) fabrics. This is a pretty niche topic. I hope I don't get stumped by too many obscure networking questions on the exam.
upvoted 0 times
...
Ammie
8 months ago
I agree with Leana. The solution provides a clear explanation, so B) No seems like the right answer here.
upvoted 0 times
...
Leana
8 months ago
The solution says the link-up delay timer is only required when split-recovery is disabled. So I guess that means the answer is B) No, it's not a guideline in this case.
upvoted 0 times
Selma
7 months ago
No
upvoted 0 times
...
Hayley
7 months ago
Yes
upvoted 0 times
...
Jordan
7 months ago
No
upvoted 0 times
...
...
Hillary
8 months ago
I'm not sure about this question. It seems pretty technical and specific. I hope the exam doesn't have too many questions like this one.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77