Cyber Monday 2024! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

HP Exam HPE7-A01 Topic 1 Question 18 Discussion

Actual exam question for HP's HPE7-A01 exam
Question #: 18
Topic #: 1
[All HPE7-A01 Questions]

With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48. how do you automate the process of resuming the port operational state once a loop on a client port is cleared?

Show Suggested Answer Hide Answer
Suggested Answer: C

Loop protection is a feature that detects and prevents loops in layer 2 networks. Loop protection can be enabled on ports, LAGs, or VLANs. When loop protection is enabled, the switch sends periodic loop protection messages on the interface and expects to receive them back.If a loop protection message is received back on the same interface, it indicates a loop and the switch takes an action to disable the interface or block traffic on it3. The loop-protect re-enable-timer command is used to configure the length of time the switch waits before re-enabling an interface that was disabled due to loop detection.The default value is 0, which means that the interface remains disabled until manually re-enabled3.To automate the process of resuming the port operational state once a loop on a client port is cleared, the loop-protect re-enable-timer command can be used with a non-zero value on the interface range that includes the client ports3. Therefore, answer C is correct.


by Amie at May 23, 2024, 03:29 PM

Limited Time Offer

25%

Off

Get Premium HPE7-A01 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Georgeanna
6 months ago
Well, I'm just glad we don't have to deal with Ethernet hubs anymore. Those were a real loop-de-loop nightmare back in the day!
upvoted 0 times
...
Lashon
6 months ago
I'm not sure about this one. Does the global timer option really make sense when we're dealing with specific client ports? I'd go with C just to be safe.
upvoted 0 times
Shala
5 months ago
I'm not sure about A, I would go with D to re-enable the timer specifically for the client ports.
upvoted 0 times
...
Veronica
6 months ago
I agree with you, A seems like the most logical option in this scenario.
upvoted 0 times
...
Regenia
6 months ago
I think A is the right choice. It disables the loop protection timer for all ports.
upvoted 0 times
...
...
Eliz
6 months ago
Option D looks good to me. Configuring the global loop-protect re-enable-timer seems like a simpler and more straightforward solution.
upvoted 0 times
Ngoc
5 months ago
I agree, it's important to have a quick and efficient way to resume port operational state after clearing a loop on a client port.
upvoted 0 times
...
Jeannetta
5 months ago
Option D looks good to me. Configuring the global loop-protect re-enable-timer seems like a simpler and more straightforward solution.
upvoted 0 times
...
Elli
6 months ago
I agree, it's important to have a quick and efficient way to resume port operational state after clearing a loop on a client port.
upvoted 0 times
...
Broderick
6 months ago
Option D looks good to me. Configuring the global loop-protect re-enable-timer seems like a simpler and more straightforward solution.
upvoted 0 times
...
...
Paris
7 months ago
Hmm, I think option C is the way to go. Configuring the loop-protect re-enable-timer on the specific client ports seems more targeted and efficient.
upvoted 0 times
Alaine
6 months ago
Yeah, configuring the re-enable-timer on specific client ports makes sense for efficiency.
upvoted 0 times
...
Samira
6 months ago
I agree, option C seems like the best choice for targeted automation.
upvoted 0 times
...
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77