Cyber Monday 2024! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25

- Free Preparation Discussions

HP Exam HPE7-A07 Topic 4 Question 24 Discussion

Actual exam question for HP's HPE7-A07 exam

Question #: 24
Topic #: 4

[All HPE7-A07 Questions]

Exhibit.

After configuring VRRP between sw-1 and SW-2. you notice that both switches are showing as active. What could be the reason for this issue?

AVRRP preemptive mode is disabled.

BSW-1 cam reach SW-2 on VLAN 10.

CBoth switches are configured as VRRP 'primary.'

DSW-2 has no priority configurations for VRRP 1.

Show Suggested Answer

Suggested Answer: C

In VRRP (Virtual Router Redundancy Protocol), only one switch should be the primary (master) for a given virtual IP address, with the other switches being backups. If both switches are showing as active, it suggests a misconfiguration where both are set to act as the primary for the same VRRP group. The exhibits provided indicate that both switches believe they are the active or primary for the VRRP group, which is an incorrect configuration.

by Antonio at Sep 15, 2024, 01:59 PM

Limited Time Offer

25%

Off

Get Premium HPE7-A07 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Joseph

2 months ago

I'm going with C. Both switches being 'primary' just sounds like a recipe for disaster. Someone needs to take a step back and reconfigure this properly.

upvoted 0 times

...

Rodney

2 months ago

Haha, imagine if both switches were just sitting there, trying to be the boss. Like a couple of kindergarteners fighting over who gets to be the line leader.

upvoted 0 times

Phil

14 days ago

D) SW-2 has no priority configurations for VRRP 1.

upvoted 0 times

...

Selma

15 days ago

C) Both switches are configured as VRRP 'primary.'

upvoted 0 times

...

Desire

1 months ago

B) SW-1 cam reach SW-2 on VLAN 10.

upvoted 0 times

...

Jeniffer

1 months ago

A) VRRP preemptive mode is disabled.

upvoted 0 times

...

Merilyn

1 months ago

C) Both switches are configured as VRRP 'primary.'

upvoted 0 times

...

Tuyet

1 months ago

B) SW-1 cam reach SW-2 on VLAN 10.

upvoted 0 times

...

Leonor

2 months ago

A) VRRP preemptive mode is disabled.

upvoted 0 times

...

...

Annice

2 months ago

Wait, wait, hold on. What if the preemptive mode is disabled? That could be the reason for the active/active state, right?

upvoted 0 times

Mitsue

1 months ago

B) SW-1 can reach SW-2 on VLAN 10.

upvoted 0 times

...

Derick

1 months ago

Yes, that could definitely be the reason for the active/active state.

upvoted 0 times

...

Rodrigo

1 months ago

A) VRRP preemptive mode is disabled.

upvoted 0 times

...

...

Jeannetta

2 months ago

Maybe SW-2 has no priority configurations for VRRP 1.

upvoted 0 times

...

Freida

2 months ago

I believe it's because both switches are configured as VRRP 'primary.'

upvoted 0 times

...

Kiley

2 months ago

I think the reason could be that VRRP preemptive mode is disabled.

upvoted 0 times

...

Kristine

2 months ago

You know, I was just thinking the same thing. Both switches being 'primary' in VRRP is definitely the problem here.

upvoted 0 times

Karima

1 months ago

We should also verify if SW-2 has no priority configurations for VRRP 1.

upvoted 0 times

...

Mitzie

1 months ago

I think the issue might be that both switches are configured as VRRP 'primary.'

upvoted 0 times

...

Jerry

2 months ago

But what if SW-1 can't reach SW-2 on VLAN 10?

upvoted 0 times

...

Marion

2 months ago

Maybe we should check if VRRP preemptive mode is disabled.

upvoted 0 times

...

...

Dorsey

3 months ago

Hmm, this one's tricky. I'd say the issue is that both switches are configured as VRRP 'primary.' That doesn't seem right.

upvoted 0 times

Stephaine

1 months ago

Maybe SW-2 just doesn't have any priority configurations for VRRP 1.

upvoted 0 times

...

Merilyn

2 months ago

Actually, I think both switches are configured as VRRP 'primary.'

upvoted 0 times

...

Cherelle

2 months ago

No, I believe the problem is that SW-1 can't reach SW-2 on VLAN 10.

upvoted 0 times

...

Mozell

2 months ago

I think the issue is that VRRP preemptive mode is disabled.

upvoted 0 times

...

...

az-700 pass4success az-104 200-301 200-201 cissp 350-401 350-201 350-501 350-601 350-801 350-901 az-720 az-305 pl-300

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77