Cyber Monday 2024! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location PL
Mob_nav_barsMENU

Juniper Exam JN0-351 Topic 1 Question 29 Discussion

Actual exam question for Juniper's JN0-351 exam
Question #: 29
Topic #: 1
[All JN0-351 Questions]

Exhibit.

You want to enable redundancy for the EBGP peering between the two routers shown in the exhibit. Which three actions will you perform in this scenario? (Choose three.)

Show Suggested Answer Hide Answer
Suggested Answer: A, B, C

Ais correct because you need to configure BGP multihop to enable redundancy for the EBGP peering between the two routers.BGP multihop is a feature that allows BGP peers to establish a session over multiple hops, instead of requiring them to be directly connected1.By default, EBGP peers use a time-to-live (TTL) value of 1 for their packets, which means that they can only reach adjacent neighbors1.However, if you configure BGP multihop with a higher TTL value, you can allow EBGP peers to communicate over multiple routers in between1. This can provide redundancy in case of a link failure or a router failure between the EBGP peers.

Bis correct because you need to configure loopback interface peering to enable redundancy for the EBGP peering between the two routers.Loopback interface peering is a technique that uses loopback interfaces as the source and destination addresses for BGP sessions, instead of physical interfaces2.Loopback interfaces are virtual interfaces that are always up and reachable as long as the router is operational2.By using loopback interface peering, you can avoid the dependency on a single physical interface or link for the BGP session, and use multiple paths to reach the loopback address of the peer2. This can provide redundancy and load balancing for the EBGP peering.

Cis correct because you need to configure routes for the peer loopback interface IP addresses to enable redundancy for the EBGP peering between the two routers.Routes for the peer loopback interface IP addresses are necessary to ensure that the routers can reach each other's loopback addresses over multiple hops2.You can use static routes or dynamic routing protocols to advertise and learn the routes for the peer loopback interface IP addresses2. Without these routes, the routers will not be able to establish or maintain the BGP session using their loopback interfaces.


by Shaniqua at Sep 17, 2024, 10:09 PM

Limited Time Offer

25%

Off

Get Premium JN0-351 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Lili
2 months ago
Whoa, this is a tough one. I'd say B, C, and D. Gotta keep those routers talking, you know? Oh, and don't forget the password - it's 'password123'!
upvoted 0 times
...
Ivette
2 months ago
Hmm, I'm thinking B, C, and D. Can't forget that MD5 authentication, it's like the secret handshake of BGP!
upvoted 0 times
Ma
1 months ago
User 3: Don't forget to configure routes for the peer loopback interface IP addresses as well, that's important for redundancy.
upvoted 0 times
...
Julieta
1 months ago
Definitely, loopback interface peering and MD5 authentication are key for EBGP peering.
upvoted 0 times
...
Ernest
1 months ago
I agree, B, C, and D are the way to go for enabling redundancy.
upvoted 0 times
...
...
Erick
2 months ago
I'd go with B, C, and E. Clustering it up for that extra layer of redundancy, baby!
upvoted 0 times
...
Ahmad
2 months ago
Definitely B, C, and D. Gotta have that redundancy and security for the EBGP peering!
upvoted 0 times
Levi
1 months ago
User 3: We should also configure routes for the peer loopback interface IP addresses.
upvoted 0 times
...
Marshall
1 months ago
User 2: Yeah, that's a good idea for redundancy.
upvoted 0 times
...
Judy
1 months ago
Absolutely, those three actions will definitely help ensure redundancy and security for the EBGP peering.
upvoted 0 times
...
Paris
1 months ago
I think we should configure loopback interface peering.
upvoted 0 times
...
Graham
2 months ago
Don't forget about configuring an MD5 peer authentication for added security.
upvoted 0 times
...
Leana
2 months ago
Yes, and configuring routes for the peer loopback interface IP addresses is also important.
upvoted 0 times
...
Melina
2 months ago
I agree, configuring loopback interface peering is essential for redundancy.
upvoted 0 times
...
...
Geraldine
2 months ago
I believe configuring routes for the peer loopback interface IP addresses is crucial for redundancy.
upvoted 0 times
...
Viki
2 months ago
I agree with Arletta. Configuring loopback interface peering is also important.
upvoted 0 times
...
Arletta
2 months ago
I think we should configure BGP multihop for redundancy.
upvoted 0 times
...

Save Cancel
az-700  pass4success  az-104  200-301  200-201  cissp  350-401  350-201  350-501  350-601  350-801  350-901  az-720  az-305  pl-300  

Warning: Cannot modify header information - headers already sent by (output started at /pass.php:70) in /pass.php on line 77